How to Stick Led Lights on Wall Without Adhesive

Want to know how to mount LED lights on a wall without using adhesive? Lucky for you! In this blog post, we will outline some of the most straightforward methods to accomplish that. We therefore have what you need, whether you’re seeking a short-term or long-term fix. To find out more, continue reading.

Why Is It Important to Mount LED Lights Without Adhesive on a Wall?

It’s crucial to mount LED lights on a wall without adhesives for a variety of reasons. The use of adhesives might harm the surface of the walls, especially if those surfaces are composed of sensitive materials like plaster or paint, which is perhaps the most evident disadvantage.

When LED lights are covered in adhesives, their effectiveness and efficiency may suffer because some of the light-emitting surface may be blocked. Furthermore, applying adhesives can be messy and time-consuming, taking away from your valuable time and attention.

For a number of reasons, LED lights without adhesive tape are a fantastic choice. It’s always better to put your lights straight onto the wall without any adhesives if you want to create accent lighting in your house or business without spending a lot of time or money!

In the end, you’ll save yourself a tonne of anxiety, trouble, and squandered resources. Why not try it now, then?

Required Materials

  • LED lights
  • Tape measure
  • Level
  • Wall anchors (optional)
  • Tape (optional)

How to Stick Led Lights on Wall Without Adhesive Step by Step Guide

Step 1: Make a Plan

A solid plan should be in place before you begin your project. You must first decide how much light you need and where to put it. This will enable you to decide how many and what size lights you require. A solid plan will make the progress of your project easier.

Step 2: Choose Your Lights

There are a plethora of various types and sizes of LED lights to pick from. Therefore, choosing which ones to employ is the first step. Once you’ve decided, you can either purchase them online or from a nearby retailer.

Step 3: Prepare the Area

Before you begin, it’s crucial to clean the area where you intend to install the lights. In any other case, muck and grime might stop the LEDs from sticking.

You must also ensure that the location is dry if you intend to use the lights outside. Wait until the area is entirely dry before moving forward if it is raining or there is dew on the ground.

Step 4: Measure

Measurements can be taken once you have a strategy and the required supplies. You must first determine the length of your LED strip and the size of the region you plan to cover. You can use this to estimate how much power you’ll require.

Step 5: Cut the Lights

It’s time to cut the light cord where it has been designated. A good set of wire cutters or scissors is required. First, cut the light string where it has been marked, ensuring sure that each bulb is facing the same way.

Step 6: Connect the Lights

It’s time to reattach your lights now that they have been cut. Twist the two ends of a battery-operated light together. The positive and negative wires of a plug-in lamp must be attached to the corresponding terminals on the wall socket or power strip.

Step 7: Stick the Lights

It’s time to attach your lights to the wall now that they are linked. Peel off the backing of the double-sided tape before pressing the lights into position. Apply a small quantity of glue to the back of the lights if you’re using it, then press the lights into position. Before continuing, allow the glue or tape to dry for a short while.

Step 8: Test the Lights

It’s time to test the lights after they have been secured in position. Make sure that all of the bulbs are illuminated and that the lights are flashing if necessary. A multimeter can be used to test the connections and make sure they are safe.

Step 9: Enjoy Your Lights!

You can now enjoy your lights because they are in place. You can use them as a night light or to highlight artwork or other wall decorations. Whatever you use them for, LED lights are a terrific way to give your house a little more character. Continue reading to learn more about how to mount led lights on a wall without using adhesive.

How to Stop LED Strip Lights From Falling Off The Wall

The majority of LED strip lights include an adhesive backing that is meant to protect them from moving around on the wall. But occasionally, this adhesive can break down, allowing the lights to come off. If this occurs, there are a few things you can do to prevent your LED strip lights from slipping off the wall.

Try cleaning the area beforehand where the lights will go. By doing this, any grit or debris that would prevent the glue from sticking will be cleared away. The surface of the wall should then be roughened with sandpaper to provide the adhesive a greater hold.

Finally, liberally spray the back of the LED strip and the wall with adhesive remover before firmly pressing them into place. Hopefully, these pointers will make it easier to keep your lights firmly in place.

How To Restick LED Strip Lights

Although it may appear difficult, resticking your LED strip lights is actually fairly easy. The preparation of the old adhesive and the application of fresh adhesive are the two key phases in resticking an LED strip.

Use a hairdryer or heat gun to gradually warm the sticky side of the strip in order to soften the current glue. By doing this, you may remove the old adhesive more easily without causing any damage to the surface underneath. Once all of the old glue has been removed, use a standard glue gun to cover the entire strip with a fresh, strong adhesive layer.

At this point, you might also want to utilise electrical tape or a particular type of mounting clip. You can quickly and easily restick your LED strip lights and get them working again with these easy steps!

How To Stick LED Strips Without Adhesives?

LED strip affixing is most frequently done with sticky tape or glue. However, there are a few ways in which this may be problematic. First off, mounting lights on a surface with glue can increase the danger of surface damage.

Additionally, because adhesive tape strips have a tendency to fray at the borders over time, it can be challenging to maintain a clean and seamless appearance. Fortunately, there are better, more effective, and cleaner methods of attaching LED strips than using traditional adhesives.

Some choices incorporate magnets or Velcro hooks, which provide a solid and safe hold while removing cleanly. Another choice is to secure the strip in place by adhering it directly to the backing material using dielectric heat shrink connectors, which heat up around the strip.

By selecting one of these alternate techniques for mounting LED strips, you can make sure that they stay put without deteriorating over time in terms of both beauty and functionality. For more details about how to mount led lights on a wall without using adhesive, keep reading.

LED strip lights can be stapled to the wall if you want to increase the amount of light in your room without using any adhesive. If you are renting and are unable to make any holes in the walls, this method is extremely useful. This is how you do it:

You must first buy some LED strip lights and a stapler. Please be careful to use small enough staples so as not to harm the LEDs.

Next, choose the location on the wall where the light strip should go. As soon as you have a general concept, begin stapling the strip to the wall. Beginning at one end, work your way down, checking the strip along the way to make sure it is level.

You might need to apply some double-sided tape to keep the LED strip in place if it is not self-adhesive. Plug the strip in and switch on the power when it has been fastened.

Can You Staple LED Strip Lights?

Although one of the most adaptable adhesives on the market, super glue is not ideal for all applications. If you want to mount your LED strip lights to a wall or other surface, for instance, you might be wondering if super glue will work. Yes, in a nutshell, but you should be aware of a few things first.

Can You Use Hot Glue on Led Strip Lights?

Yes, you can attach LED lights to a wall without needing adhesive by using hot glue. First, press the light against the wall after applying a little amount of hot glue on the rear of the lamp. You’re good to go after holding it in place for a brief period of time while the glue hardens.


LED lights mounted without glue are the ideal choice if you’re searching for a quick, simple, and economical way to add more light to your walls.

You’ll be able to enjoy your new illumination in no time if you use the proper sort of light and follow these easy instructions. Thank you for reading our article on how to mount LED lights without using adhesive.

About The Author

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top